Author: Lone_Sentry_Admin

Categories
German

28 cm Rifled Projectile

German 28 cm Rifled Projectile

This pre-engraved projectile recovered in Italy is used for long range bombardment. It has longitudinal inclined steel splines and a single one-inch-wide copper band that acts as a gas seal. The splines are set at a slight angle to the axis of the projectile and are 19.2 inches in length. In loading the projectile, the splines are lined up with the rifling of the gun tube. The shell is 33 inches in length, exclusive of the windshield. Fragments indicate that the windshield would add an extra two feet to the length.

A nose percussion fuze (AZ 35 K) and a base fuze (BD Z 35K) are fitted. The Germans are reputed to have four types of 28 cm railway guns able to employ this type of projectile. They are: 28 cm Br. N. Kan E.; 28 cm K. 5 (E); 28 cm K. 5/1 (E); and 28 cm K. 5/2 (E).

SPECIFICATIONS

Caliber         280 mm (11.023 ins.)
Weight (approx.) 550 lbs.
Length (excluding windshield) 33 ins.
German: p. 312

Categories
German

10.5 cm HL, HL/A, HL/B, HL/C: Hollow Charge Ammunition

10.5 cm HL, HL/A, HL/B, HL/C: Hollow Charge Ammunition

There are four known variations of the 10.5 cm (105 mm) hollow charge ammunition fired from the German 10.5 cm le. F. H. 18 series:

Type Hl has a deep conical cavity, a short ogive, and flash tube extending through the shaped cavity to the fuze booster. All types have an additional detonator booster combination at the base of the flash tube.

Type Hl/A has the same shaped cavity but has a larger diameter flash tube that is attached to the apex of cavity liner by a pressed collar, and does not extend into the cavity. This type has a long ogive.

The principal difference between types Hl/A and Hl/B is in a shallower, hemispherical-shaped cavity. The principal difference between types Hl/B and Hl/C is the addition of a funnel-like steel washer inverted over the cavity. This funnel is supposed to counteract the effects of centrifugal force on the hollow charge jet.

The explosive filler is pressed into two pellets in types Hl/A, Hl/B, and type Hl/C. Explosive fillers in all rounds are inclosed in waxed paper cartons. The metal ogive screws into the projectile, holding all components of the filler in place.

The aluminum fuze (AZ 38) carries the primer detonator. It is armed by centrifugal force and contains no other safety features. It functions by a “spit” from the booster, which travels down the central tube and initiates the base booster, and hence the main bursting charge.

ESSENTIAL MODIFICATIONS

Type Hl/A: (a) Lengthened nose-piece (ogive), giving greater standoff. (b) Elimination of flash tube between fuze and apex of cavity and larger diameter of flash tube.

Type Hl/B: (a) Further increase of standoff obtained by shortening the HE filler. Nose piece is identical with that of Type Hl/A. (b) Hemispherical cavity instead of rounded cone. (c) HE filling RDX/WAX, instead of RDX/WAX/TNT.

Type Hl/C: Introduction of a washer, shaped like an inverted funnel in front of the cavity. Otherwise, types B and C are essentially identical.

SPECIFICATIONS

        Hl       Hl/A       Hl/B       Hl/C
Weight of projectile as fired:25.8 lb.27.1 lb.26.6 lb.27.2 lb.
H.E. filling, carton, wax: 4.6875 lb.3.5 lb.3.255 lb.
Empty shell: 22.55 lb.22.937 lb.22.315 lb.
Collar (“funnel”)   .5195 lb.
Muzzle velocity f/s*1375136013601360

Estimated performance at normal against Homogeneous armor.
     Type Hl/A—170 mm (static) 105 mm (dynamic)
     Type Hl/B—155 mm (static) 100 mm (dynamic)
     Type Hl/C—155 mm (static) 100 mm (dynamic)
                       (From German claims)

*Firing with charge five which is normally used.

German: p. 310 (August 1, 1945)

Categories
German

8 cm Wurfgranate 39: 8 cm Mortar Shell “Bouncing Betty”

8 cm Wurfgranate 39: 8 cm Mortar Shell - Bouncing Betty

The 8 cm Wgr. 39 consists of a nose fuze, front cap, rear body, and tail assembly. The body, which is separated from the cap at the ogive, has a standard shape and TNT filling. The cast nose cap fits over a cylindrical boss, concentric with the longitudinal axis of the projectile. This cap is secured to the boss by four shear pins that extend through the cap and the boss. The seam where the two parts are joined is then shellacked to form a watertight seal.

An impact type, nondelay fuze is screwed into the cap; inside the cap is a plastic container of about 1 1/2 ounces of smokeless powder. Under the charge, screwed into the projectile body, is an iron plug with a small axial hole through it. This plug separates the smokeless powder charge from the combination delay pellet and booster which is in an aluminum container.

The tail assembly is a standard type, having the usual base charge, ring increments, and fin assembly.

Upon impact, the nondelay fuze ignites the smokeless powder charge, sending a flash through the hole in the separating plug, setting off the delay pellet. The explosion from the first charge shears the pins holding the nose cap to the projectile body, and throws the shell from 5 to 10 feet into the air. In the meantime, the booster detonates the main TNT bursting charge at approximately the moment when the projectile is at the height of its bounce. This gives the effect of an air burst without the use of a precision time fuze. Height of the burst is governed by the angle of the shell axis with the ground at the time of impact.

KEY TO PARTS:
     (A) Propellant increments
     (B) Propellant cartridge
     (C) Projectile body
     (D) False ogive
     (E) Point ignition fuze—Wgr. Z 38 st
     (F) Booster well
     (G) Booster capsule
     (H) Delay type detonator
     (I) Paper washer
     (J) Paper diaphragm
     (K) Plastic washer
     (L) Booster well adapter
     (M) Ejector capsule
     (N) Ejector capsule igniter

German: p. 309 (August 1, 1945)

Categories
German

7.5/5.5 cm Pzgr. Patr. 41 (W): 7.5 cm Pak 41 Armor-Piercing Ammunition

7.5/5.5 cm Pzgr. Patr. 41 (W): 7.5 cm Pak 41 Armor-Piercing Ammunition

This round is designed for use in the 7.5/5.5 cm Pak 41 tapered bore antitank gun described on page 123 of this volume. It is an armor piercing tracer projectile of Gerlich design with the nomenclature 7.5 cm Pzgr. Patr. 41 (w).

The projectile consists of an outer case, a tungsten carbide core 1.16 inch in diameter, a screw head, a ballistic cap, and a tracer. It is fired from a regular cartridge consisting of cartridge case 6344, primer C/12n. A. St., an igniter of pyroxylin porous powder, and the propelling charge of diglycol tubular powder.

SPECIFICATIONS

Total weight of round        16.65 lb.
Total length of round        29.8 ins.
Weight of projectile        5.68 lb.
Weight of tungsten carbide core        2.01 lb.
Diameter of core        1.16 ins.
Weight of propellant charge        5.4 lb.

German: p. 306.2

Categories
German

15 cm Stielgranate: 15 cm Stick Grenade

15 cm Stielgranate: 15 cm Stick Grenade

The German 15 cm high explosive Stick Grenade is reported to be used with the 15 cm heavy infantry gun, s. I. G. 33. Its prime purpose is for demolition, and for clearing minefields and wire obstacles. Of welded steel construction, the bomb has a 1/8-inch case consisting of three main parts: the nose, a cylindrical center piece, and a tapered rear piece. Both the nose and the base are reinforced with steel rings welded to the casing. The ring in the nose is tapped to receive the fuze adaptor; that in the base to accommodate a steel cup. This cup, which has machined surfaces, is 3/8-inch thick at the base and 3/16-inch at the sides. A stick unit which leaves the bomb approximately 150 yards from the muzzle of the gun fits over the cup. According to reports, the unit weighs 22.2 kg. (49 lb.) and the propelling charge 5.5 (12 1/8 lb.).

The main filling consists of approximately 60 pounds of poured 50/50 Amatol. A 2-inch cylindrical booster charge made up of compressed T.N.T. pellets is located in the center of the main filling about 15 inches from the booster; two normal annular picric pellets surround the booster. The bomb is fitted with a percussion type nose fuze, Wgr. Z. 36, which is also reported as being used in the German 20 cm Spigot Mortar Bomb. The tail, of unusual construction, has three tubular steel sockets equally spaced around the bomb and projecting from the rear portion of the casing at an angle of 20° to the main axis. These sockets receive tubular bars to which the sheet steel tubular fins are attached. The bars are bent in order to bring the fins parallel to the main axis and also to provide clearance of the muzzle of the gun. In addition there are six 5/32-inch steel plate fins welded to the casing and spaced in pairs between the tubular sockets.

SPECIFICATIONS

Overall length        50 1/2 ins.
Overall length (excluding tail fins & fuze) 30 3/4 ins.
Diameter (maximum) 11 1/2 ins.
Thickness of casing 1/8 in.
Total weight (approx.) 105 lb.
Weight of filling (approx.) 60 lb.
Color Field grey

German: p. 306.1

Categories
German

Topf Mine: Antitank Mine

Topf Mine: Antitank Mine

The Topf Mine, a completely non-metallic, waterproof, antitank mine, consists of a circular body filled with a 12 1/2-pound charge of TNT, a primer plug assembly, and an igniter. The top of the mine is flat, with a fixed pressure plate in the center slightly higher than the surface; a 4 1/2-inch circular recess located in the bottom takes the primer plug and igniter assembly. The outer casing is made of a hard pulp-like material covered with pitch. The mine rests on three glass studs; two of the studs secure a pasteboard carrying handle, while the third, which is sometimes larger than the two others, is used as a filler plug.

The primer plug assembly consists of a glass screw cap and a cylindrical wooden booster holder, the top of which has a deep threaded recess to take the Topf Mine Igniter. A subsidiary igniter socket in the glass cap leads to the booster charge, and is threaded to take a standard igniter.

The Topf Mine Igniter, which is made of glass, has no safety device. It comprises a cylindrical glass body 3 mm thick; a solid glass pressure head, hemispherical in shape and two small glass ampules, one of which contains sodium and potassium as a liquid alloy and the other ethyl nitrate. The ampules are held in position by a black celluloid disc. A thin bakelite detonator well is provided.

The mine is activated by a pressure of at least 330 pounds, which forces the pressure plate down onto the igniter head and thereby breaking the two glass ampules. A flash results, setting off the detonator, booster, and main charge. If a standard igniter is used, the mine must be laid upside down.

SPECIFICATIONS

Diameter of mine        12 1/2 ins.
Height of mine 5 1/2 ins.
Weight (complete) 20 lbs.
Weight in crate 29 lbs.
Filling TNT
Weight of filling 12 1/2 lbs.
Firing pressure 330 lbs.
Height of igniter (including cap) 3 1/2 ins.
Diameter of igniter body 1 1/2 ins.
Shear pressure of igniter 132 lbs.
Overall height of primer plug assembly 3.1 ins.
Diameter of primer holder 2 1/2 ins.
Diameter of glass cap 4.6 ins.

German: p. 304.9 (May 1, 1945)

Categories
German

S. Mi. 44 mit S. Mi. Z. 44: Antipersonnel Mine

German S. Mi. 44 mit S. Mi. Z. 44: Antipersonnel Mine

This anti-personnel mine is basically the same, both in construction and operation, as the S. Mi. 35 described on page 305. It consists of an outer casing and an inner cylinder which contains a T.N.T. charge surrounded by small shot. There are three threaded openings in the cover plate: one is used for pouring the charge into the mine; the second, which takes a S. Mi. Z. 44 igniter, opens into a tube containing a 4.5 second delay pellet and a propellant consisting of three grams of fast burning gun powder; the third which is closed by a wooden plug leads into a tube containing a detonator, a flash cap, and a pull igniter. The pull igniter, located at the base of the tube, contains a spring-loaded striker held in place by two steel balls which are prevented from moving by a pin in the base of the igniter. The pin is attached to the base of the outer case by approximately three feet of coiled wire.

The S. Mi. Z. 44 is a percussion igniter differing from the usual percussion type in that it has two small wings which, when forced outward by pressure from above or tension through trip wires from the side, release the spring-loaded striker to fire the cap. A pressure of 21 pounds or a tension of 14 pounds will actuate the igniter.

Operation of the igniter initiates the 4.5-second delay pellet which fires the propellant throwing the mine upwards. When the coiled wire is fully extended (about 2 1/2 feet above ground level) it pulls the pin from the igniter, enabling the retaining balls to move inward and release the striker to fire the flash cap, detonator, and bursting charge.

SPECIFICATIONS

Height        5 1/8 ins.
Height with igniter 8 7/8 ins.
Diameter 4 ins.
Weight 8.8 lb.
Color Camouflage yellow

German: p. 304.8

Categories
German

Glasmine 43 (f): Glass Mine (Antipersonnel)

Glasmine 43 (f): Glass Mine (Antipersonnel)

The mine consists of an outer glass casing, the upper portion of which is 1/4-inch thick and the lower portion 2/5-inch thick. The external diameter at the base is 4 1/2 inches and at the top, 6 inches at the widest part.

A grooved shoulder on the inside of the case, about 2 inches from the bottom, supports the igniter plate. The mine may employ either a Buck chemical igniter or a new mechanized igniter, the Schuko. When the latter is used, the igniter plate consists of a thin sheet metal plate, which has a central hole for the igniter. When the Buck igniter is used, however, an igniter plate having the same diameter and igniter hole but of stronger design is employed. Around the top of the case is a grooved ledge which supports a thin glass shear plate approximately 1/32-inch thick.

A moulded glass pressure plate of 3/4-inch extreme thickness and 4 1/2 inches in diameter rests on the shear plate. There are two parallel grooves on the underside of the pressure plate which are designed to accept a metal safety fork that will bridge the outer edge of the mine and support the pressure plate until such time as the mine is laid. The two prongs are then withdrawn through the two grooves arming the mine. This fork is not supplied with the mine but is improvised by units.

Four raised strips moulded in the bottom of the mine are spaced so as to take a standard 200 gm. charge (Sprengkorper 28). When sufficient pressure (40 lbs.) is applied to the glass pressure plate, the shear plate is broken and crushes the top of the Buck igniter or trips the actuating lever of the Schuko igniter, depending on which is employed.

SPECIFICATIONS

Weight of standard charge        200 gm
External diameter at top        6 ins.
External diameter at base        4.5 ins.
Height to lip of container        4.2 ins.
Thickness of casing (upper)        .25 in.
Thickness of casing (lower)        .4 in.

German: p. 304.6 (March 1, 1945)

Categories
German

Haft-Hohlladung 3 Kg.: Magnetic Hollow Charge Antitank Mine

Haft-Hohlladung 3 Kg.: Magnetic Hollow Charge Antitank Mine

The German magnetic, hollow-charge, antitank mine, designed for use by tank-hunting squads, consists of a main filling of TNT in a pressed metal container of conical shape. The conical container has an elongated apex threaded externally at its upper end to receive a closing cap. The closing cap is fitted with a detonator well, and threaded internally to receive a standard (B.Z.E.) friction igniter which has a 4.5 second delay.

The base of the cone is attached to a plywood framework. Three horseshoe type magnets, sufficiently powerful to cause the mine to adhere to a vertical surface, are fixed to the bottom of the frame. During transit, the magnets are fitted with a keeper. A brass chain terminating in a hook is also attached to the frame.

SPECIFICATIONS

Weight of live charge       7 lbs., 12 1/2 oz.
Weight of explosive (TNT) 1 lb., 15 1/2 oz.
Weight of booster (Pentrite) 3 oz.
Height of charge 10 3/4 ins.
Height of bursting charge container 7 3/4 ins.
Height of magnets 2 3/4 ins.
Height of apex of hollow cone 6 7/16 ins.
Diameter of base of hollow cone 4 3/16 ins.

German: p. 304.5 (March 1, 1945)

Categories
German

Panzerwurfmine (L): Hollow Charge Antitank Hand Grenade

Panzerwurfmine (L): Hollow Charge Antitank Hand Grenade

The Panzerwurfmine (L) consists of a metal body and a wooden handle to which four canvas fins are attached. The grenade is intended to be thrown by hand, and is armed by the removal of a metal cap at the base of the handle. This cap not only acts as a fuze cover, but also serves to hold the fins close against the handle of the grenade before throwing.

The body is made in two pieces crimped together and attached to the handle by a metal band. It contains an 18 1/2 oz. filling of 50/50 R.D.X./T.N.T. cast around a hollow charge liner made of pressed steel.

A sensitive impact fuze consisting of a striker, a creep spring, and two steel balls is located in the base of the handle. The two balls fit into a recess in the striker and are held outward by a safety pin fitting between them, causing them to bear against the top of the striker housing and preventing the striker from moving down onto the primer. Beneath the primer in the base of the handle is a detonator and a picric acid booster. A small length of tape is attached to the safety pin at one end, and is held in at the other end by the metal cap and a semicircular clip attached to one fin and fitting around the handle.

When the grenade is thrown, the fins which are attached to the handle by steel ribs open out umbrella fashion, and the clip attached to one fin is pulled away from the housing. This action releases the tape which unwinds and pulls the safety pin out of the striker. During flight, the two steel balls move in, freeing the striker which compresses the creep spring on impact, setting off the primer, detonator, booster, and main filling.

SPECIFICATIONS

Overall length          21 ins.
Length of body 9 ins.
Length of fins 11 ins.
Diameter of body 4 1/2 ins.
Weight (approx.) 3 lb.
Filling Cast R.D.X./T.N.T.
Color of body Grey

German: p. 304.4